Wall Sawing Services in Abu Dhabi

Precise, low-vibration cuts through reinforced concrete walls, with clean edges and minimal disturbance to the surrounding structure. Al Raihan Rental provides wall sawing across Abu Dhabi for door and window openings, AC and MEP penetrations, lift shafts and structural modifications, with night and weekend work available for occupied sites.

Method Statement

Supplied

Fully Insured

For Your Protection

10+ Years in UAE

Years Experience

Own Machines

Trained Operators

Our Clients

Trusted By Leading Companies

WALL SAWING

When You Need a Wall Saw

A track-mounted diamond saw is the right method when you need a clean, square opening through concrete that is too thick or too heavily reinforced for a handheld cutter, and when breaking is not an option because of noise, dust or structural risk.

 

Door and Window
Openings

Cut into existing RCC and block walls during villa, office and retail refurbishments.

 

AC Duct & Ventilation Openings

Sized to the drawing so the unit seats flush with no unnecessary patching.

 

Plumbing & Electrical Penetrations

Grouped MEP openings coordinated to a single service run where required.

 

Lift Shafts & Stair Openings

Cutting through structural slabs and shear walls for new access and building works.

 

Controlled
Demolition

Remove a defined wall section without disturbing the surrounding structure.

 

Structural Wall
Cutting

Cutting on load-bearing elements to an engineer’s approved drawing.

 

Because the blade cuts rather than impacts, wall sawing is close to vibration-free. That is why it is specified in hospitals, hotels, data rooms and older buildings where breaking would risk cracking finishes or disturbing adjacent structure.

 

PRE-CUT SCANNING

We Scan Before We Cut

The most expensive mistake on a concrete opening is hitting something inside the wall. A severed conduit or a cut water line turns a half-day job into a week of remedial work and a claim.

 

Every opening is scanned before the blade goes in. We locate rebar, post-tension cables, conduits and embedded services, then mark the cut line around them or bring the position back to your consultant if the opening needs to move.

 

CUTTING CAPABILITY

Cutting Capability

Most enquiries come down to two questions: can you get through the depth, and can you handle the rebar.

 

Specification

Capability

Wall Types

Reinforced concrete, RCC, block and precast

Reinforcement

Heavy rebar cut clean, with no spalling or tearing

Post-tensioned elements

Assessed case by case with your structural engineer

Cutting depth

Confirmed against your wall thickness at survey. Deeper walls are cut from both faces where access allows

Machine type

Track-mounted diamond wall saw

Cut orientation

Vertical, horizontal and inclined

Flush cutting

Against adjacent walls and floors

Opening shape

Rectangular openings cut square to drawing dimensions

Site power

Site supply where available, or our own power on site

Dust and slurry

Wet cutting with closed vacuum slurry recovery

Edge finish

Square and chamfer-free, ready for framing

CONCRETE REMOVAL

Getting the Concrete Out

Cutting the opening is half the job. A 400 mm reinforced section a metre square weighs close to a tonne, and how it leaves the building is what decides your programme.

We size every cut to what can be safely handled on your site. Where sections can be manoeuvred by hand, we cut them into manageable panels. Where they cannot, we bring lifting equipment and rig the section out under a controlled lift.

Removal of cut sections from the work area is included as standard. Disposal off site can be added to the scope on request.

 

WORKING AT HEIGHT

Openings at Height

Not every opening is at ground level. Facade penetrations, upper-floor AC openings and warehouse wall cuts all need a stable working platform, and hired-in access is usually where the programme slips.

We supply our own access equipment alongside the cutting crew, so the platform arrives with the saw on the same mobilisation. One supplier, one schedule, no waiting on a third party to deliver a lift before your job can start.

 
 

AREAS WE SERVE

Where We Work in Abu Dhabi

Our crews cover the emirate, from the industrial zones through to the islands and the city centre.

 

Mussafah & ICAD

Khalifa City

Mohammed Bin Zayed
City

Shakhbout City

Al Reem Island

Al Maryah Island

Yas Island

Saadiyat Island

Corniche

Al Mushrif

Central Abu Dhabi

Al Raha

Industrial sites come with their own hurdles. Gate passes, site inductions and HSE documentation all have to be in order before a crew gets past security, and a team that turns up without them costs you half a day. We know what each site expects and we arrive with the paperwork sorted, so the job starts when it is scheduled to start.

Site surveys are carried out across Abu Dhabi, usually within a day of your enquiry.

 

OUR PROCESS

How the Job Runs

1. Site survey
We measure the opening, check wall thickness and reinforcement, and confirm access, power and water. No charge inside Abu Dhabi city.
2. Method statement and approvals
You receive a written method statement, risk assessment and insurance documentation for your main contractor or building management. We advise on structural engineer sign-off where a load-bearing element is involved.
3. Scanning and isolation
Services are located, live systems isolated, the area sheeted and slurry containment set up.
4. Cutting
The saw is track-mounted and the cut made in controlled passes, dust-suppressed throughout.
5. Removal and handover
Sections are lifted out, the area is cleaned down, and the opening is handed over ready for the next trade.

SAFETY & COMPLIANCE

Safety, Permits and Structural Clearance

Written Safety Documentation

Every job runs under a written method statement with a task-specific risk assessment. Our operators are trained and certified, and we carry public liability cover with documentation issued before mobilisation.

 
 

Structural Clearance

Where the wall is load-bearing or forms part of a shear element, we will not cut until an approved structural drawing or engineer’s confirmation is in place. We can work alongside your consultant to sequence propping and temporary support.

 
 

Occupied Building Protection

For occupied buildings, we run wet cutting with vacuum slurry recovery and schedule night or weekend shifts to keep disruption off your operating hours.

 
 

REVIEWS

What Our Clients Say About Us

Our reputation is built on quality work and customer satisfaction. See what homeowners, contractors, and businesses say about our core cutting, concrete cutting, and demolition services across Dubai.

 

WALL SAWING COST

What It Costs

Wall sawing is quoted on linear metres cut, adjusted for depth and reinforcement. A 200 mm block wall and a 400 mm reinforced shear wall are very different jobs at the same length.

 
 

What Your Quotation Includes

Your quotation accounts for cut length and wall depth, reinforcement density, access and working height, water and power availability on site, shift timing, and whether disposal is included.

 
 

Clear, Site-Specific Quotations

Quotations are issued within 24 hours of the site visit, with a minimum call-out charge on smaller jobs.

 


Within 24 Hours

Quotation after site visit

SCOPE OF WORK

What Is and Isn’t Included

Included

Not Included

We will tell you up front which trades you still need. Nobody likes finding out on handover day.

WHY CONTRACTORS USE US

Why Contractors Use Us

We own the machines.

No waiting on a third-party supplier, no markup layered onto your rate.

 

We turn up when we say.

A delayed opening holds up every trade behind it, so mobilisation windows are confirmed in writing.

 

We leave the site clean.

Slurry recovery, sheeting and clean-down are scope, not extras.

 

We handle the paperwork.

Method statements, risk assessments and insurance certificates come up front, so your HSE manager is not chasing us.

 

One supplier, full scope.

Wall sawing, core cutting and concrete cutting and demolition from the same crew, with access equipment included.

 

Frequently Asked Questions

What is Wall Sawing?

Wall sawing is a cutting method that uses a diamond blade mounted on a track fixed to the wall. The track guides the blade in a perfectly straight line, producing a square opening with clean edges. It is used where an opening needs to be accurate and where breaking would create unacceptable dust, noise or structural risk.

How Does Wall Sawing Works?

A track is anchored to the wall along the cut line and the saw head travels along it, driven hydraulically or electrically. The blade enters in stages, deepening with each pass until it breaks through. Water cools the blade and captures dust, and the slurry is vacuumed away as the cut progresses.

How deep a wall saw can cut?

 Our saws cut up to [XXX] mm in a single pass. Deeper walls can be cut by working from both faces where access allows. Send us the wall dimensions and we will confirm before mobilising.

Can wall saws can cut reinforced concrete?

Yes. Diamond blades cut straight through rebar without tearing the surrounding concrete or leaving spalled edges. Reinforcement density affects cutting time, not whether the cut is possible.

Can you cut concrete walls for doors and windows?

Yes, and it is the most common job we do. Openings are cut square to your drawing dimensions so the frame seats without packing or patching.

What is the difference between wall sawing and core drilling?

Core drilling produces a round hole, typically for a pipe, cable or duct passing through a wall or slab. Wall sawing produces a straight-sided opening of any size and shape. If you need a circular penetration, core drilling is faster and cheaper. If you need a door, window or a rectangular opening, you need a wall saw.

Is wall sawing suitable for structural concrete?

Yes, provided the modification is approved. We cut structural and load-bearing elements regularly, but only against an engineer’s drawing or written confirmation, with propping sequenced where required.

Can I rent a telehandler near me?

Telehandler rental can be arranged depending on your project location and equipment availability. Contact us with your location and required machine specifications.

 

How long does concrete wall cutting take?

A standard door opening in a reinforced wall is usually cut and removed within a single shift. Lift shafts, multi-cut jobs and openings at height are scheduled after the site survey.

Which Areas of Abu Dhabi do you Cover?

The full emirate, including Mussafah, ICAD, Khalifa City, Al Reem Island, Yas Island, Saadiyat Island and the city centre. [Al Ain and Ruwais on scheduled mobilisation.]

Need a Wall Cut in Abu Dhabi?

Tell us the wall dimensions and the site location. We will confirm feasibility, give you a mobilisation window, and send the method statement your contractor needs.

 
WelldoneStar